[title]
[message]Inclusive Inc
Angle Adjustment Plate for Wheelchair Frame Fixed Angle Bracket
WC-AAP
$50.00 USD
-
vammaisille -
Takuu -
Lainattu ostoskoriin
About the Wheelchair Adapter Plate (WC-AP)
The Wheelchair Adapter Plate (WC-AP) is used to mount to chairs or mounts that have a hole spacing associated with it.
Wheelchairs that have a series of holes along the seat rail can typically be mounted with a WC-AP.
This plate fits 1/4" or 6mm bolts, and spans from 1 inch [25mm] to 2 inches [50mm].
Once attached, the Wheelchair Adapter Plate (WC-AP) can mount to the hardware below:
- Adjustable Wheelchair Bracket WB(Adjustable)
- Solid Wheelchair Bracket WB2(Solid)
- Wheelchair L-Angled Extension Plate Wc-lae
- Pyörätuolisovitinlevy 2 WC-AP2
Wheelchair Adapter Plate (WC-AP)
Wheelchair Frame with Hole Spacing
(Round & Square/Rectangular)
Attaching an Adapter Plate to Wheelchair Frame with Hole Spacing
- 3/16 "HEX -avain (jokainen kiinnityskuoren kanssa)
- 7/16" Socket, Box, Open or an Adjustable-End Wrench
- Determine that the hole spacing on the wheelchair is accommodated by the Adapter Plate (WC-AP).
If there are several options, choose the widest span possible.- Largest hole spacing can accommodate holes spaced up to 2 inches apart [50 mm]
- Smallest hole spacing can accommodate holes spaced 1 inches apart [25 mm]
- Orient the Adapter Plate to best suit the specific mounting location (it can be flipped so the threaded mounting holes are above or below the bolt points).
- Thread both the provided bolts (1/4"-28 x 2" long) through the hole and slot to line up with the wheelchair hole spacing.
- Screw the bolts into the provided locknuts, and tighten.
Example 1: Mounting to Wheelchair Frame with Hole Spacings (Round Tubing).
The picture on the left shows someone lining up the WC-AP to the wheelchair frame holes.
Hole spacing on this particular chair (the Quickie P220) is 1".
Footrest removal is not obstructed in this setup, and the WC-AP could be moved rearward on the wheelchair frame to accomodate if it did.
Example 2: Mounting to Wheelchair Frame with Hole Spacings (Square/Rectangular Tubing).
This picture shows an Adapter Plate (WC-AP) attached to a rectangular rail with hole spacing. If you look closely (click on the picture to enlarge) you can see that there are two holes that can be mounted to.
The larger hole spacing is selected in favor of the tighter hole spacing for the broadest base of support.
Example 3: Mounting to a pre-existing hardware.
There are many instances where a wheelchair already has some mounting hardware attached.
Assuming that the pre-installed hardware is robust enough, it may be easier for people to mount onto that hardware.
Shown above are the Adapter Plate (WC-AP) mounted onto an unknown mounting system, and onto Daedelus systems Multi Hole Adapter.
Nämä ovat vain muutamia esimerkkejä siitä, kuinka jotkut ihmiset ovat onnistuneesti asentaneet pyörätuoleihinsa.
Ymmärrämme, että jokainen tapaus on erilainen, joten jos sinulla on kysyttävää asennuksesta tai kiinnitystä varten, yleensä
F.A.Q
Lisää valinnainen kuvaus tähän osaan
Lähetämme seurantatiedot tilaukseesi liittyvään sähköpostiosoitteeseen, kun kohde on lähettänyt. Jos et ole saanut seurantatietojasi ja se on ollut yli 2 arkipäivää, ota meihin yhteyttä numeroon (012) 123 - 4567
Liittyvät tuotteet
Äskettäin katsottu
Äskettäin toivottu
Lisää valinnainen kuvaus tähän osaan